PC1616/PC1832/PC1864 User Manual v4.5 and higher. FCC COMPLIANCE STATEMENT. To be repaired by the end user. DSC c/o APL Logistics 757 Douglas Hill Rd, Lithia Springs, GA 30122 Additional Information. In series with and ahead of all other equipment attached to the same tele.
Advertising
[310]-[311] Partition Identifier Codes
Enter a 6 digit Maintenance Code
[350] – Communicator Format Options
This section determines the communication format used for central
station reporting. From the chart listed below program the 2-digit num- ber for the desired format for the first and second telephone number
[367] – Opening/Closing Call Direction Options
The first toggle option in this section is used to enable/disable opening/
closing reporting for partition 1. To enable opening/closing reporting turn option [1] ON. Configure the options as required and press [#] to exit
.
[377] Communication Variables
NOTE: For UL Installations, the Entry Delay plus the Communications
Delay must not exceed 60 seconds.
[380] – First Communicator Option Codes
[381] – Second Communicator Option Codes
The 3rd toggle option in this section is used to enable/disable auto-
matic SIA reporting. The 5th toggle option is used to enable/disable automatic Contact ID reporting. Configure the options as required and press [#] to exit.
NOTE:If the automatic SIA or automatic Contact ID reporting formats
are not used, reporting codes must be programmed. To program reporting codes refer to the PowerSeries PC1616/1832/1864 Refer- ence Manual which can be downloaded from the DSC web site at
www.dsc.com
[382] – Third Communicator Option Codes
The 4th toggle option in this section is used to enable/disable Call
Waiting Cancel. Configure the options as required and press [#] to exit. NOTE:A Call Waiting Cancel on a Non Call Waiting line will prevent successful connection to the central station.
[701] – First International Options Codes
Option 7 in this section Selects Battery Charge Options.
Select ON for 7 Ahr and 14 Ahr batteries (700 mA charge rate) Select OFF for Standard 4 Ahr batteries (400 mA charge rate)
[310 System Acct. Code
I___II___II___II___II___II___I
[311] Partition 1 Acct. Code
I___II___II___II___I
Def
Enter 2 digits From Chart Below
![]()
04
04
I___II___I
I___II___I
NOTE: 3rd Phone Number follows the format of the
1st Phone Number
01 20BPS, 1400 Hz Handshake
02 20BPS, 2300 Hz Handshake 03 DTMF Contact ID 04 SIA FSK 05 Pager 06 Residential Dial
07 10BPS, 1400 Hz Handshake
08 10BPS, 2300 Hz Handshake 09 Private Line 10 Scantronics 4-8-1 Fast Slo 12 Robofon 13 CESA 200
Opt
Default
Description
1
I__I
ON
1st Telephone Number
✔
OFF
Disabled
2
I__I
ON
2nd Telephone Number
✔
OFF
Disabled
5
I__I
ON
Alternate Communicator
✔
![]()
OFF
Disabled
Def
Enter 3 digits as indicated below
003 I___II___II___I
003 I___II___II___I
003 I___II___II___I
000 I___II___II___I
030 I___II___II___I 010 I___II___II___I
030 I___II___II___I
030 I___II___II___I
007 I___II___II___I
030 I___II___II___I
000 I___II___II___I
Swinger Shutdown
(Alarms and Rest. Swinger Shutdown (Tamper and Rest. Swinger Shutdown (Maint. and Rest. Communication Delay AC Failure Comm Delay TLM Trouble Delay
Test Transmission Cycle
(land line) Not Used Zone low Battery Transmission Delay Delinquency Transmis- sion Cycle Communications Cancelled Window
(001-014 Transmissions)
(001-014 Transmissions,
000=disabled) (001-014 Transmissions, 000=disabled) (000-255 seconds) (001-255 minutes) No. of checks req’d (003- 255) (001-255 days/minutes)
(000-255 days)
(000-255 days/hours)
(000-255 minutes)
NOTE: Option 1 is defaulted to 001 for CP-01 Installations
Option 4 is defaulted to 030 for CP-01 Installations
Option 11 is defaulted to 005 for CP-01 Installations
Opt
Default
Description
1
I__I
✔
ON
Dsc Power Series Pc1832 Manual
Communications Enabled
OFF
Communications Disabled
2
I__I
ON
Restorals on Bell Time-out
✔
OFF
Restorals Follow Zones
3
I__I
ON
Pulse Dialing
✔
OFF
DTMF Dialing
5
I__I
ON
3rd Telephone Number Enabled
✔
OFF
3rd Telephone Number Disabled
8
I__I
ON
Delinquency Follows Zone Activity (Hours)
✔
OFF
Delinquency Follows Arming (Days)
Opt
Default
Description
3
I__I
ON
SIA Sends Programmed Reporting Codes
✔
OFF
SIA Sends Automatic Reporting Codes
5
I__I
ON
Contact ID Uses Programmed Reporting
Codes
✔
OFF
Contact ID Uses Automatic Reporting Codes
Opt
Default
Description
4
I__I
ON
Call Waiting Cancel Enabled
✔
Free shipping refers to standard ground shipping only.
![]()
OFF
Call Waiting Cancel Disabled
5
I__I
Pc1616 Pc1832 Pc1864 User Manual
ON
T-Link Interface Enabled
✔
OFF
T-Link Interface Disabled
Dsc Pc1832 User Manual
Opt
Default
Description
Dsc Pc1832 Install Manual
7
I__I
ON
High Current Battery Charge (700mA)
✔
OFF
Standard Battery Charge Rate (400mA)
Advertising
This manual is related to the following products:
Popular Brands
Popular manuals
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |